Press "Enter" to skip to content

How to Update the Firmware and Factory Reset Your Adtran MX-2800

adminwho 0

Updating the firmware on your MX-2800 ensures you are using the latest, most stable version of the multiplexer possible. Adtran releases firmware updates for free and are definitely worth the time to upgrade your network. The firmware for the multiplexer can be downloaded directly from Adtran’s website.

Before we continue, you following is required in order to complete this process.

• A populated MX2800 Chassis (1200290L1)

• A DB9 to RJ-45 serial cable for consoling into the MX-2800

• A network switch to connect both your MX-2800 chassis and your PC to the same network.

• A TFTP Program for transferring the.bin file from your PC to the multiplexer. We use SolarWinds TFTP as it is both free and easy to navigate.

• A program to console into the multiplexer and send commands to it. We use PuTTY because of its versatility

Start by running the serial cable from your computer’s COM port to the multiplexer’s console port. Connect your MX-2800’s LAN port to the network switch you are using. The PC should also be connected to the same switch.

Move the.bin file you downloaded from Adtran (in our example this is 1205288L1a_342a_1f5f.bin) to your TFTP-Root folder and make sure that your TFTP-server is up and running. Also take this time to find out your computer’s IP address. You will need this information as well when transferring the firmware update to your multiplexer.

Once you have that information and your TFTP server is running, you’ll want to launch PuTTY. Select connection type ‘Serial’ and specify a Baud rate of 9600. Once you are in the console hit enter until you see a screen appear asking for your username and password. Enter your username and password combination. If you do not know this, the default answers are written below:

Username? adtran

Password? adtran

Once logged into the multiplexer, you’ll want to enter 3 for configuration. Hit ‘Enter’ to proceed to the configuration page. Here you’ll want to hit 3 again to get system management. You’ll want to enter an IP address and Gateway IP Address for your MX-2800. We set our IP address to 192.168.1.26 and the Gateway address to 192.168.1.1 but you will want to set these values to whatever is appropriate for your network.

In order to enter the IP address, select 1 and then punch in the IP address you’re using. The same is done for the Gateway address by selecting the option 2. Once you have inputted your code, back out t othe configuration page by pressing the ESC key.

Now select option 4 (Utilities) from the Configuration menu to enter the System Utilities screen. Here you will see the two system controller cards loaded in your system. We will want to update these mx-2800 system controller cards to version 3.42A.

To start, press 2 for ‘Update FLASH Software’ and press 2 again for ‘Update via TFTP server.’ Enter your PC’s IP address and type in the server file name of the.bin file you wish to transfer from. Once these values are correct enter 3 to being the transfer.

**Warning** Do not disconnect the MX2800 at all during this process. Any sudden power loss or change in state can cause irreparable damage.

Once you are finished head back to the ‘System Utilities.’ You’ll now want to load default settings by using option 1. This will take you to the ‘Load default settings’ screen. Select option 3 to reset your multiplexer back to default. Confirm by entering 1. Once this is done, back out by pressing ESC twice.

You will know you are done when both cards installed are set to code version 3.42A. One of the cards may not be displaying correctly. This can take a few minutes to update, so be patient. Once both cards display correctly you will know you are finished! Feel free to power down the system or resume using the system as you were before.

Source by Fred Tardie

Leave a Reply

Your email address will not be published. Required fields are marked *